Skip to content Skip to navigation menu

Mark3 HP Moisture Analyzer

Mark 3 is a flexible moisture analyzer system for labs and production facilities. Its optional modular add-ons provide the best solution for every measuring task.

Its high-resolution weighing system also makes the Mark 3 HP suitable for precisely analyzing the moisture and water content of very dry samples. This feature makes it a genuine alternative to Karl-Fisher titration.

Item no.:  LMA100-SET-P

Availability:  On Request

Mark 3 HP Moisture Analyzer with printer, consisting of:

  • LMA100PA-000U control module incl. printer
  • LMA100PQ-000U heater module (0.1 mg, 100 g)
  • optional on request: Moisture Analysis individual Service (YMD01P)


  • Economical and reliable alternative to the Karl-Fischer titration and drying oven methods
  • Intuitive operation – With a learning curve of a few minutes
  • The user starts the measurement by pressing just one button
  • Robust and fast, optimal for routine operation
  • Multi-module operation enables parallel measurements of up to 4 different samples on one single device
  • An extensive range of security settings guarantees reliable results and 100% traceability

Application Note

Mark 3 Moisture | Solids Analyzer
en 156.4 kB
Mark 3 Moisture Analyzer
en 155.5 kB
Mark 3 Moisture Analyzer
en 144.6 kB
Mark 3 LTE Moisture Analyzer
en 155.8 kB
Mark 3 LTE Feuchtebestimmer
de 154.7 kB
Mark 3 Moisture Analyzer
en 157.3 kB
Mark 3 Feuchtebestimmer
de 156.1 kB
Mark 3 Feuchte- | Feststoffbestimmer
de 155.4 kB
Mark 3 Moisture Analyzer
en 178.8 kB
Mark 3 Feuchtebestimmer
de 154.4 kB
Mark 3 Feuchtebestimmer
de 159.4 kB
Mark 3 Feuchtebestimmer
de 178.0 kB
Mark 3 Moisture Analyzer
en 160.5 kB
Mark 3 Feuchtebestimmer
de 143.5 kB


Mark 3 HP Feuchtebestimmer — modularer Infrarot-Feuchtebestimmer mit Quarzstrahler
de 394.0 kB
Mark 3 HP Moisture Analyzer — Modular Infrared Moisture Analyzer with Quartz Radiator
en 393.7 kB

Product properties

  • Recommended moisture range
    0.001 – 99.999%

Technical attributes

  • reproTEST
    Built in reproTEST for determining the repeatability of the weighing system
  • Data Printer
    Thermal printer, built-in
  • Additional Product Specifications
    • Display of results: 0.001%
    • Balance resolution: 0.0001 grams
    • Balance capacity: 100 grams
    • Balance repeatability: +/-0.0001g
    • Recommended working range: 0.005 to 99.995%
    • Method of Measurement: Loss on drying via four infrared quartz cylinders
    • Modular configuration: Control and Heater modules (Optional: up to 4 heater modules)
    • Temperature setting/control: 30–210° C in one degree increments via RTD sensor, +/- 1°C
    • Temperature steps: Programmable one or two with selectable ramp rate
    • Temperature adjustment: Optional fixture for internal electronic two-point adjustment
    • Standby temperature: 30–160°C in one degree increments with selectable equilibration time
    • Temperature display: Display of both target and current temp at each stage of testing and standby
    • Conserve mode clock: Programmable time by day of week to shut down and wake up analyzer
    • Balance module design: Monolithic weighing cell with protective stainless steel cover
    • Balance calibration: Internal calibration weight or external weights accepted for manual calibration
    • Ideal weight: Audio and visual signal when ideal weight is reached
    • Target limit alert: Minimum and maximum programmable limits and screen alert when test done
    • Program storage: 300 programs with unique settings, alphanumeric naming
    • Result storage: 999 results with statistics: Average, SD, RSD, high and low
    • Units of measure of results: Weight, %Moisture, %Solids, %Volatiles, PPM moisture, PPM drying mass, mg/L
    • Endpoint determination: Actual slope, Calculation and Time modes
    • Sample ID: Numeric, incremental, alphanumeric or turned Off
    • Modes of operation: Standard test, Syringe, "Splash" method or Concentration modes
    • Operator names: Twenty alphanumeric operator names
    • Security mode: Selectable setup and operation protection with numeric code
    • Graph mode: Graph of temperature and percentage over time
    • Display: Quarter VGA with contrast adjustment (black on white or white on black)
    • Keypad: Sealed membrane with audible tactile feedback
    • Internal printer: Built-in thermal, 40 character graphic with selectable format
    • Power requirements: 90–250 VAC 50/60 Hz self adjusting power supply
    • Dimensions (L × W × H): 16.25'' × 19.5'' × 9.25'', shipping weight 35lbs (includes one heater module)
    • Warranty period: 2 years, complete parts and labor